PBI microbial air sampler ( DUO SAS 360 ISOLATOR )

DUO SAS 360 ISOLATOR

DUAL HEAD PORTABLE MICROBIOLOGICAL AIR SAMPLER Single body with two separated aspirating heads: two separate head can be place in two different environments. The DUO-SAS-360 ISOLATOR features: • The technical performances are the same as SAS Super 180 • The high flow rate of 360 litres per minute (180+180 litres) is ideal for low contamination environments, for example Clean Rooms where it is necessary to test a large volume of air • Two different heads may be used for simultaneous samples in different environments • Up to ten sequential sampling cycles for “in operation” monitoring according to USP recommendations • High speed sampling: 1000 litres in less than 3 minutes (500 per head) • Potentially up to 18 cubic meters of air / hour may be monitored • It can be used either with 55 mm Contact plates (U.S., or European made) , 84 mm Maxi Contact plates or 90 mm Standard Petri dishes. Code Description 91746 Duo Sas 360 Isolator air sampler - for Contact Plates 91796 Duo Sas 360 Isolator air sampler - for Petri Dishes

PBI microbial air sampler (SAS SUPER ISO)

SAS SUPER ISO YOUR PARTNER IN ENVIRONMENTAL MICROBIOLOGY The very familiar “yellow SAS (Surface Air System)” is considered the international standard for portable air microbiological samplers. Over 25 years experience has been gained in five continents helping microbiologists in the pharmaceutical and food industry, hospital sector and indoor air quality fields. Experience has also been gained from space exploration as the SAS (Surface Air System) was used on board the International Space station. This knowledge has resulted in the development of the new “SAS-ISO 100” and “SAS-ISO 180”. THE BASIC IDEA • To use a simple plate for air and surface sampling • To have the additional flexibility of choice, either Contact plates or Petri dishes • To apply cGLP and cGMP to air sampling operations • To establish data on the microbial level in selected environments • To organise sequential sampling to obtain a more representative air sample under actual operating conditions The “SAS – ISO” has the following new features: • Performance in compliance with ISO 14698-1 • Large LCD with illuminated touch panel • All operator commands via touch keypad for easier cleaning • Over 70.000 litres of air / 8 hours autonomy • Infrared transfer of sampling data to PC or printer • Up to 300 sampling cycles memorised • USP chapter < 1116 > and 21-CFR 11 Compliance • Sampling rate accurately maintained by speed sensor-incorrect aspiration aborts cycle • Design avoids turbulence in unidirectional air flow and re-aspiration of tested air in accordance with ISO specifications • Total traceability • Bi-directional port to input and output data to a central unit from 1 to 24 samplers • Calibration system by finger-tip control without opening the instrument • Automatic calibration reminder • Easy calibration monitoring with additional anemometer system • Sampler can be operated whilst attached to mains Established «yellow SAS (Surface Air System)» features and performances are maintained: • Possibility to use 55 mm or 84 mm Contact plates (RODAC) and standard disposable 90 mm Petri dishes • Interval sampling with fully programmable parameters for “in operation” monitoring • Delay Start of up to 60 minutes • Infrared remote control (optional extra) • Certified aspirating head in aluminium or stainless steel • Multiple language choice • Reduced sampling time (six or ten minutes for 1000 litres of air) • Suitability in isolator Plus a worldwide service and support network which includes: • International PBI is the only company with its own microbiological wind tunnel to test the air samplers from a microbial point of view • Complete validation documentation available to help the local validation process • Product specialists provide on-site training and certification of personnel for the proper usage of the air samplers • Official factory calibration in Milan performed in 48 hours • Over 100 Application Notes • Standard Operating Procedures (SOP) • I.Q., O.Q., P. Q. documentation or on-site activation Code Description 86279 SAS SUPER ISO with air flow of 100 l/min for Contact Plate (without head and transformer) 86834 SAS SUPER ISO with air flow of 180 l/min for Contact Plate (without head and transformer) 90719 SAS Super ISO 100 with air flow of 100l/min for Petri dishes (without head and transformer) 90720 SAS Super ISO 180 with air flow of 180l/min for Petri Dishes (without head and transformer)

PBI microbial air sampler (DUO SAS 360 )

DUO SAS 360

DUAL HEAD PORTABLE MICROBIOLOGICAL AIR SAMPLER
Single body with two aspirating heads: two separate plates may be used for simultaneous sampling to differentiate micro-organisms (onto two different media) or onto the same media to calculate an average value and to obtain a more representative result

The DUO-SAS-360 features:
• The technical performances are the same as SAS Super 180
• The high flow rate of 360 litres per minute (180+180 litres) is ideal for low contamination environments, for example Clean Rooms where it is necessary to test a large volume of air
• Two different media types (e.g.: Total Bacterial Count and mould / yeast media) may be used for simultaneous samples
• Up to ten sequential sampling cycles for “in operation” monitoring according to USP recommendations
• High speed sampling: 1000 litres in less than 3 minutes (500 per head)
• Potentially up to 18 cubic meters of air / hour may be monitored
• It can be used either with 55 mm Contact plates (U.S., or European made) , 84 mm Maxi Contact plates or 90 mm Standard Petri dishes

Code	Description
24584	DUO SAS 360 air sampler with air flow of 180 l/min per head for Contact Plates (without head and transformer)
90718	DUO SAS Super 360 air sampler with air flow of 180l/min per head for Petri dishes (without head and transformer)

Demo of PBI microbial air sampler

ROTRONIC( Humidity Indicators, Transmitters, Data Loggers and Generators)

Transmitters

The ROTRONIC humidity transmitters, temperature transmitters and dew point transmitters are designed for fixed installation in applications ranging from the control of office buildings, storage areas and manufacturing processes to specialized applications such as IT rooms, server rooms, clean rooms, pharmaceutical test laboratories, stabilization rooms and semi-conductor fabrication areas.


view all transmitters

Portable Indicators

The HygroPalm is a highly accurate hand-held indicator that displays relative humidity, temperature and the dew or frost point. The HP21 is perfect for spot checking HVAC installations, manufacturing and storage areas, and generally for all ambient air measurement within the temperature range of -10 to 60°C (14 to 140 °F). The key features of the HygroPalm will meet user requirements ranging from the most basic to demanding.

view all portable indicators

Data Loggers

Select from two basic models of humidity temperature data loggers. The HygroLog is a simple-to-use data logger with a single humidity temperature probe. The HygroLog HL-NT humidity data logger complies with FDA 21 CFR Part 11 and features multi-probe capability and advanced functions such as networking, automatic remote data download, monitoring of external contacts, relay outputs, etc.


view all loggers

CO2 Measurement

The concentration of CO2 is as an important indicator for the quality of room air. A high CO2 content can cause rapid fatigue and loss of concentration. This becomes noticeable more quickly in small rooms in which there are many people. A climate control system can maintain suitable air quality by increasing the supply of fresh air based on a measurement of CO2 concentration as opposed to just measuring relative humidity and temperature.


view all CO2 Measurement

Humidity Generators

The HygroGen HG2 humidity generator is a calibrator for up to five relative humidity probes simultaneously. The HG2 humidity generator typically requires less than 5 minutes to equilibrate from one humidity condition to another when temperature is kept constant. The HG2 features a user friendly touch screen graphical interface as well as a programmable ramp and soak function with multiple steps and profiles.


view all humidity generators

Water Activity

ROTRONIC offers fast and accurate instruments for the measurement of water activity of foods, seeds, pharmaceuticals, cosmetics, etc. Our unique technology also guarantees water activity measurement at the lowest possible purchase price. We offer a choice of three water activity systems that all use the same high precision to ensure consistently precise results and full interchangeability between the quality control laboratory and production areas.

view all water activity

Probes

Based on the AirChip 3000 technology, the HygroClip 2 humidity, temperature and dew point probes are designed for use with our indicators, data loggers and transmitters and can also be used as a stand-alone probe, digital or analog. The HygroClip 2 probes can be configured with the ROTRONIC HW4 software



view all probes

Meteo Products

Airport weather stations, meteorological towers, rooftop installations and any application with continuous data monitoring. Available with different supply voltages, including 115 VAC.

TOC Analyzers - Shimadzu Scientific Instruments

TOC-L Series

TOC Analyzers

• Top
• Improvements from the TOC-V Series（TOC-VCSH/CPH/CSN/CPN）
• Improvements from the TOC-5000 Series
• 680 °C Combustion Catalytic Oxidation Method Measurement Principles
• TOC-Control L/V
• Data Reliability Assurance Support
• TOC-L Virtual Advisor
• Configure a TOC-L

The TOC-L series of TOC analyzers adopts the 680°C combustion catalytic oxidation method, which was developed by Shimadzu and is now used worldwide. 　While providing an ultra wide range of 4 μg/L to 30,000 mg/L, these analyzers boast a detection limit of 4 μg/L through coordination with NDIR. This is the highest level of detection sensitivity available with the combustion catalytic oxidation method. 　In addition, the combustion catalytic oxidation method makes it possible to efficiently oxidize not only easily-decomposed, low-molecular-weight organic compounds, but also hard-to-decompose insoluble and macromolecular organic compounds. For more information on this method, click here.

Extremely wide measurement range from 4 μg/L to 30,000 mg/L, applicable to everything from ultrapure water to highly contaminated water （TOC-LCSH/CPH）

• Capable of TC, IC, TOC (= TC-IC), and NPOC measurement; options enable POC (volatile organic carbon), TOC via POC + NPOC, and even TN (total nitrogen) measurements
• The blank check function evaluates system blanks by measuring ultrapure water processed automatically within the instrument
• The automatic dilution function enables measurements up to 30,000 mg/L

Reliable sample injection system

• Automatic sample acidification and sparging
• The automatic dilution function reduces sample salinity, acidity, and alkalinity, significantly extending the period of use of catalysts and combustion tubes (The period of use depends on the sample and measurement conditions.)
• Stat or priority samples can be added at anytime to the analysis schedule without interrupting operation even when an autosampler is used

Select from 4 models to suit your application

The TOC-L series consists of a high-sensitivity model with a detection limit of 4 μg/L, making it suitable for a variety of applications, including pure water measurements, and a standard model designed with cost performance in mind. Each analyzer is available as an LCD and keyboard-equipped standalone model, or as a PC-controlled model.

In addition, the USB format has been adopted as the external interface, enhancing the equipment's versatility. Even the standalone models are capable of output to a general-purpose PC printer or to a USB memory stick.

TX714A Large Alpha Polyester Swab (MOL 5.020")

Quantity Option Bag: 100 Swabs Per Bag (2 Inner Bags of 50 Swabs)
Quantity Option Case: 10 Bags of 100 Swabs Per Case

The ITW Texwipe TX714A Large Alpha Swab is a polyester swab for cleaning broad surfaces and flat areas. Its laundered, knitted Alpha polyester head is extremely clean. A long, rigid handle and large internal head paddle provide firm support. The Alpha Swab is widely recommended for surface sampling and cleaning-validation work. Its cleanliness levels provide a neutral background for the sample obtained. This swab is an ideal choice for controlled cleaning and sampling of large areas.

ITW Texwipe TX714A Features:

- Cleanroom-laundered, double-layer knitted AlphaLite polyester tip over full-sized, rigid paddle
- Long, light green polypropylene handle
- Thermally bonded head
- Soft and nonabrasive

ITW Texwipe TX714A Benefits:

- Ultra-low nonvolatile residue
- Low particle and fiber generation
- Good sorbency
- No contaminating adhesives
- Excellent chemical resistance

ITW Texwipe TX714A Applications:

- Cleaning with solvents such as IPA
- Sampling surfaces for TOC or cleaning validation
- Applying lubricants and other liquids
- Removing excess materials

ITW Texwipe TX714A Dimensions:

- Head width = 12.7 mm (0.500")
- Head thickness = 4.2 mm (0.165")
- Head length = 25.7 mm (1.012")
- Handle width = 5.2 mm (0.205")
- Handle thickness = 3.0 mm (0.118")
- Handle length = 101.8 mm (4.008")
- Total swab length = 127.5 mm (5.020")